Skip to main content

Our cookie policy

Close

We use cookies to give you the best possible experience of our website. If you continue, we'll assume you're happy for your web browser to receive all cookies from our website. See our cookie policy for more information on cookies and how to manage them.


  • how-to-fix-a-dripping-tap

    How to fix a dripping tap

    20 March 2018
    Like this article Tweet this article Share this article +1 this article
 
  • A dripping tap isn't just annoying; it also has the potential to be really expensive. And we're not just talking about it running up your water bill – it can cause serious property damage, costing about £387 million in insurance claims annually. You can avoid the hassle of repairs and build up your no-claims bonus by keeping your home well maintained.

    Like bleeding a radiator, fixing a dripping tap is a really simple skill that every homeowner should learn how to do. Our handy guide will talk you through it, whether this is your first time or you just need a refresher.

    What you'll need

    Get these things together first and keep them nearby, because you don't want to be running off looking for an important part in the middle of your repair:

    • an adjustable spanner
    • slot and cross-head screwdrivers
    • scissors
    • replacement cartridge or assorted washers and O-rings

    Cartridge or washer?

    Some taps use washers while others have ceramic discs. An easy way to tell what kind of tap you have is to give it a turn – if it only rotates a quarter or a half, then it's likely to be ceramic. If you can turn it further, it's probably traditional. Worn O-rings are another cause of leaks in traditional taps, so if you replace the washer and there's still a leak, check the O-ring (a type of seal) and seals for signs of wear and tear.

    Step 1: Turn off the water

    Either turn your water off at the stopcock or at the isolation valve – this is usually found on the pipes underneath the sink. Run the tap until there's no more water left.

    Turn off the water

    Step 2: Find the screw

    The screw holds the tap together, and you'll need to loosen it to get inside and make repairs. It's usually hidden underneath the decorative hot and cold caps on top of the tap, or under the hot and cold indicator on single lever taps. You can usually unscrew these caps by hand, or pop them off gently with a slot-head screwdriver.

    Tip: put the plug in the sink before unscrewing anything. That way you won't lose anything important down the drain.

    Find the screw

    Step 3: Take your tap apart

    As well as the caps and the screws you'll also need to take off the tap's head (the bit you turn). There might be a metal cover around the neck of the tap protecting the valve. If so, take this off too. Lay all your bits and pieces out on the side of the sink, in order of when you took them off, so that it's easy to put your tap back together again.

    Step 4 is slightly different depending on your tap, and the type of repair you need to make.

    Take your tap apart

    Step 4: Replacing a ceramic disc

    Once you take off the metal shroud you'll be able to see the valve. Grip it with your adjustable spanner and turn it until it's loose enough to be removed. Pop your replacement cartridge in and tighten it. Put your tap back together.

    Replace ceramic disc

    Step 5: Replacing a rubber washer

    Use your adjustable spanner to grip and turn the valve until it's loose enough to be removed. Unscrew or slide the rubber washer off, and put a new one on. Put the valve back in, tighten it, and put your tap back together.

    Replace rubber washer

    Step 6: Replacing an O-ring

    The O-ring is a bigger washer at the bottom of your tap spout. Unscrew the grub screw at the base of the spout, and then lift the spout off carefully. You'll be able to see the O-rings at the base. Use your flat-head screwdriver to loosen the O-ring and slide it off, or just snip it off with a pair of scissors. Roll the replacement O-ring on. Pop the spout back where it belongs, and tighten the grub screw.

    Replace O-ring